![]() ![]() For example, we noticed a propensity to bend up to notes, which produces the wrong note output. One is the pitch wheel that shows you how close to your intended pitch you’re singing. If you’re challenged in that area, there are a couple of tools to help, but they take some getting used to. If you can sing in tune, the pitch portion of Dubler is highly effective. Melody makerĪside from the Triggers mode, the other half of the software is called Controls, and it converts your voice into melodic MIDI pitch data and your vowel sounds into MIDI CC messages that can be mapped to any parameter in your DAW or instrument. And if you want your kicks and snares to land consistently, you can disable Velocity Control on each drum trigger individually. You can bring life to drum parts quickly, especially closed hi-hats. The fantastic thing about Dubler is how well the drum triggers track velocity. We also had several double triggers early on but fixed these with the Input Sensitivity control. But, that’s more to do with the consistency of playing/beatboxing than the software. No matter what your sound source is, you’re unlikely to trigger the right drum all of the time. Once you begin recording drums in your DAW, the results are very useable, especially if you keep the number of triggers to a minimum. Making the sounds different is critical for avoiding mistriggers, and this saves time in MIDI editing later. If beatboxing isn’t your thing, you can train the drum triggers to respond to claps, chest-beating, finger clicks and any other distinct sound. It turns out that the ‘ti’ and ‘ts’ sounds that you might reasonably expect to work for closed and open hi-hat triggers are too similar and can confuse the Vochlea engine. By starting with just three elements: ‘boo’, ‘ti’ and ‘ka’ sounds, we had much greater success and could snappily turn out some drum and bass breaks. Our first attempts failed pretty miserably. To get the most out of Dubler, you’ll also want to record a bit of yourself beatboxing to understand what sounds you actually make when beatboxing rather than the sounds you think you make. It’s a good idea to keep a glass of water close by because refining your beatboxing style can be thirsty work, and when your mouth is dry, you won’t make such distinct sounds. You’ve got to make sure that you define sounds that are different enough that you don’t cause mistriggers. The clean UI makes this is highly intuitive. This is as simple as making that noise into the mic a few times. ![]() To define each trigger sound, you need to train the software. You can assign these to any musical key but starts on C1 by default to trigger a kick drum. ![]() In the Triggers mode, Dubler can interpret up to eight different trigger sounds. While you can set your own mic as the input device for Dubler, this latency doubles when using a regular mic plugged into an interface, even with a DAW buffer size of 32 samples. Any latency when using the Dubler USB mic is virtually imperceptible. The two main criteria for assessing any audio-to-MIDI system, particularly one that involves live tracking, are latency and triggering accuracy.įor drums, triggering is impressively fast. After all, Dubler is acting as both a MIDI input device and a control surface. This is critical because there are a few settings in your DAW that you might not know to change. Any help would be appreciated and log files can be provided.Setup is very straightforward, and there are easy-to-follow tutorial videos on Vochlea’s YouTube channel to get you started. Sometimes not just the program but also the whole software seems to lag like it was explained in another forum ( Lag time between pressing "play" on UR and program start with UCG-1.1.1 - DoF)…Īfter the upgrade to UR Software 5.6.0 I still have the same problem. A reinstall of the URCap leads again to the same behaviour (lag of two minutes). If I uninstall the External Control URCap, then the lag is reduced to just a few seconds but this is still slightly slower than prior the first URCap installation. If I start a different program (not ROS related), then the program start takes around two minutes as well but the execution works normally, i.e. However, it takes around two minutes before the program actually executes and shows that the connection to the remote PC could not be established (IP and URCap settings should be fine because on the day before it was already working). After starting the robot driver on my ROS PC, I also started the robot program using the play button. I installed the External Control URCap and created a new program ‘extCtrlROS’ as explained in the setup guide. We would like to use ROS for the control of our robot and installed the recommended ROS driver ( GitHub - UniversalRobots/Universal_Robots_ROS_Driver: Universal Robots ROS driver supporting CB3 and e-Series). We have an issue with our new UR10e robot. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |